Barix extreamer to megaseg6/11/2023 ![]() ![]() All mentioned trademarks belong to their respective owners and are used for reference only. Enter your design's WAN Stream Transmitter's (UDP) Even Port Number in the Port text box. ![]() Select RTP from the Protocol drop-down list. On the VLC Main Menu select Media > Open Network. All information is subject to change without notice. Download and install the latest open source VLC media player. Please follow the Safety and Precaution Recommendations. Barix is a ISO 9001:2015 certified company. ![]() Find them in the download section at Find your distributor on this list for more hardware.įor questions that are extending the documentation, feel free to contact us on:Įmail: information and the use of this product including all services are covered under the Barix Terms & Conditions and our Privacy Policy. Safety and precaution recommendations apply. Increase the separation between the equipment and receiver.Ĭonnect the device into an outlet on a circuit different from that to which the receiver is connected.Ĭonsult the dealer or an experienced radio/TV technician for help. Reorient or relocate the receiving antenna. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: However, there is no guarantee that interference will not occur in a particular installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Network settings)Ĭheck the descriptions below to see how the LEDs are supposed to behave once the system is “ready”įor more details on IP Audio Client, the software running on IP Former consult the IP Audio Client user manual. LED1 blinks slowly during the boot up processĪs soon as device enters rescue mode, LED1 starts blinking YELLOWįactory defaults setting (RESET button pressed >10s)Īfter 10s of holding RESET button pressed, LED1 starts blinking fast GREEN to indicate that the RESET button can be released and that the default factory settings will be applied (incl. Right after power-up both status LEDs are red (boot in process)ġ5s after power-up → Device announces its IP Address (take note to be able to enter the web interface later) → Left LED turns from red to greenģ5s after power up → Application is ready → Right LED turns from red to greenĮxstreamer M400 is ready to be configured. Plug the power chord into the power connector on the back panel of the device. STEP 2 Connect the networkĬonnect your Exstreamer M400 to the network using a standard Ethernet cable (CAT5e or better). The Exstreamer M400 provides an unbalanced line level output ( nominal at 0dBu), to be connected to a mixer, a DSP, an amplifier, etc. Installation STEP 1 Connect the Audio Equipment The Barix Exstreamer M400 is an audio over IP decoder with a line-level output on stereo RCA connections. Power Supply Unit (depends on the PN purchased) Refer to the IP Audio Client user manuals ( Standard Mode - AES67 Mode) for a complete explanation on the software functionalities. At the end of this guide the user will be able to run a basic setup and have an audio stream playing.Įxstreamer M400 runs the IP Audio Client software. The scope of this document is to give a thorough introduction on the Exstreamer M400. Line level (4.Please make sure to first read the safety information in order to avoid hazards.USB 1.1 interface for flash memory, (FAT16/32 file-system support).Streaming support with UDP, RTP, HTTP, Shoutcast, Multicast.Audio stereo decoder for MPEG1&2 Layer3 (MP3), HE-AAC v2 (AAC+), WMA, Ogg Vorbis,16bit PCM linear and a-law, u-law, 8-48k sample rate support.Installing the Barix Exstreamer 100 is fast and simple due to its unique features, SonicIP and IPzator: On power up the device finds a correct IP address and announces it over the audio and headphone outputs. With serial and Ethernet control APIs, it can also be managed from typical automation systems. The Barix Exstreamer 100 provides unbalanced RCA outputs and a headphone jack, along with Ethernet connection and web-browser control. The Barix Exstreamer 100 plays MP3, G.711 and PCM audio files from PC or web server (http) as well as legacy digital and analog sources (using the Barix Instreamer) and streams from sources like Shoutcast, Icecast (Internet radio) or RTP servers (Instreamer). It enables users to create flexible, cost-effective distributed audio systems using standard IP technology. The Barix Exstreamer 100 is a versatile network audio decoder for a variety of applications. ![]()
0 Comments
Leave a Reply. |